Description
360 Key Pad
Original AquaThruster™ 360 Oscillator Replacement Part
Restore Programming Control With a Replacement 360 Key Pad
The 360 Key Pad is the replacement white keypad for Original AquaThruster™ 360 Oscillator units. It is the control you use to program how far and how fast your oscillator sweeps the waterfront.
Whether your keypad is worn, cracked, faded or no longer responding reliably, this replacement part restores seamless programming and operation of your AquaThruster™ 360 Oscillator without replacing the entire control assembly.
Only the keypad is having problems? This is the part you need. If the circuit board is also failing on a white-keypad unit, you will need the complete 360 Board Kit instead.
Original 360 Oscillator White Keypad Units Programming Control Genuine AquaThruster™ Part
Replacement white keypad for the Original AquaThruster™ 360 Oscillator.
Key Pad or Full Board Kit?
Keypad issues only Buttons worn, cracked or not responding, with the circuit board working: order this 360 Key Pad.
Circuit board issues (white keypad) Upgrade to the complete 360 Board Kit, which replaces the board and the keypad.
Nexa 360 owners The Nexa 360 uses its own 360 Board Kit for Nexa 360.
PROG
Restores Programming
Program rotation range and sweep timing for your 360 Oscillator again.
FIT
Direct Replacement
Made for the Original AquaThruster™ 360 Oscillator white-keypad control.
$
Lower-Cost Repair
Replace only the keypad when the circuit board is still working.
360
Keep the Unit Working
Get your oscillator sweeping the shoreline again instead of running in one direction.
Disconnect power before servicing. Unplug both the AquaThruster™ motor and the 360 Oscillator before opening the oscillator cover or replacing the keypad.
Not sure if it is the keypad or the board? Call 877-224-4899 before ordering.
Questions About the 360 Key Pad?
Call Weeders Digest at 877-224-4899 for help choosing the right equipment for your lake or pond.
Compatibility
Is the 360 Key Pad Right for My Unit?
| Your Unit & Problem | Part to Order |
|---|---|
| Original AquaThruster™ 360 Oscillator, white keypad, keypad problem only | 360 Key Pad (this part) |
| Original AquaThruster™ 360 Oscillator, white keypad, circuit board problem | 360 Board Kit (replaces board and keypad) |
| AquaThruster Nexa 360 | 360 Board Kit for Nexa 360 |
Upgrading to the 360 Board Kit? The newer board and keypad hardware uses updated programming steps, and the kit includes new instructions for installation and programming.
Specifications
360 Key Pad Specifications
| Product | 360 Key Pad |
|---|---|
| Type | Replacement keypad (white) |
| Used On | Original AquaThruster™ 360 Oscillator |
| Function | Programming and operating the 360 Oscillator |
| Quantity | 1 keypad |
| Not Included | Circuit board, blue cover |
How to Replace
Replacing the 360 Key Pad
- Unplug the AquaThruster™ motor and the oscillator.
The motor and the 360 Oscillator each have their own power cord. Disconnect both before you touch the unit. - Remove the unit from the water if needed.
Work on a dry, stable surface where small screws will not be lost. - Remove the blue cover.
Take out the cover screws and lift off the cover to reach the keypad. - Swap the keypad.
Disconnect the old keypad and connect the replacement keypad in the same position. - Reinstall the cover.
Check the cover screws and rubber washers and replace any that are worn so the cover seals properly. - Reprogram the oscillator.
Restore power and program your rotation settings following your owner’s manual.
Missing or worn cover screws? Order the Cover Screw with Rubber Washer.
Related Tools
Products That Work With the 360 Key Pad
Related Weeders Digest products to consider with the 360 Key Pad.
FAQs
360 Key Pad FAQs
Answers to common questions about the 360 Key Pad.
What does the 360 Key Pad do?
It is the control you use to program and operate the Original AquaThruster™ 360 Oscillator, including the rotation range and sweep timing.
Do I need the 360 Key Pad or the 360 Board Kit?
If only the keypad is worn or unresponsive, order the 360 Key Pad. If the circuit board on a white-keypad unit is failing, order the complete 360 Board Kit, which replaces both the board and the keypad.
Will this keypad fit the Nexa 360?
No. The Nexa 360 uses its own 360 Board Kit for Nexa 360.
Will I need to reprogram my oscillator?
Yes. Plan to re-enter your rotation settings after installing a new keypad, following your owner’s manual.
Is the blue cover included?
No. The 360 Blue Cover is sold separately.
Which AquaThruster™ do I have: Original 360 Oscillator or Nexa 360?
The Original AquaThruster™ uses the separate 360 Oscillator attachment, programmed from a white keypad on older units or a black keypad on newer units. The Nexa 360 is the newer integrated system with keypad-controlled rotation and motor tilt, Lift Assist and one-pin Quick-Attach mounting. If you are unsure, call 877-224-4899 with your order information or a photo of the unit.
Who can help me confirm the right part?
Call Weeders Digest Product Support at 877-224-4899 or contact Weeders Digest Product Support. Having your order information and a photo of your unit makes matching the part quick.
4 Reviews
-
The 360 key pad very nice and the aqua Thruster Works fantastic.
Very easy to install and works great
-
Works as advertised
Works as advertised
-
Very good
Peace of cake to install
-
Oscillator keypad would not accept program Ming
Part arrived in a timely manner Worked as it should have. Problem was the DC voltage from the the step down wasn’t reaching the board due to the oxidation of the butt splice at the occolater control box. After new splice works like new. Price ya pay for not troubleshooting with a multimeter